System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.C3600 processor with 32768 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled
program load complete, entry point: 0x80008000, size: 0x4ed478 Self decompressing the image :

##############################################
#######################

################
#########

####################

##############################
#####################

####################
?[OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 16-May-00 12:26 by ccai
Image text-base: 0x600088F0, data-base: 0x60924000

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID 25125768
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y
您是否進入初始化配置對話,選Y
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.Basic management setup configures

only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: n
您是否進入基本配置安裝,選N
First, would you like to see the current interface summary? [yes]: y
首先,您是否看一下當前端口狀態
Any interface listed with OK? value "NO" does not have a valid configuration

Interface IP-Address OK? Method Status Protocol
FastEthernet0/0unassigned NO unset up down
Serial0/0 unassigned NO unset down down
FastEthernet0/1unassigned NO unset up down

Configuring global parameters:

Enter host name [Router]:RouterA
輸入路由器的名字
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: aaa
輸入密文
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: bbb
輸入密碼(不能和密文相同)
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: ccc
輸入虛擬終端的密碼(以備遠程登錄)
Configure SNMP Network Management? [yes]: n
配置簡單網管嗎?選N
Configure IP? [yes]: y
配置IP嗎?選Y
Configure IGRP routing? [yes]: n
配置IGRP路由選擇協議嗎?選N
Configure RIP routing? [no]:
配置IGRP路由選擇協議嗎?選N
Configure bridging? [no]:
配置橋接嗎?選N
Async lines accept incoming modems calls. If you will have
users dialing in via modems, configure these lines.

Configure Async lines? [yes]: n
配置異步線路嗎?選N
Configuring interface parameters:

Do you want to configure FastEthernet0/0 interface? [yes]: y
您是否想配置fastethernet0/0接口?選Y
Use the 100 Base-TX (RJ-45) connector? [yes]: y
用RJ45的連接器嗎?選Y
Operate in full-duplex mode? [no]: y
選用全雙工模式?選Y
Configure IP on this interface? [yes]: y
在這個接口上配置IP嗎?選Y
IP address for this interface: 192.168.0.1
配置該接口的IP地址(在此地址為192.168.0.1
Subnet mask for this interface [255.255.255.0] :
配置該接口的子網掩碼.(默認的是255.255.255.0,可以手工輸入修改)
Class C network is 192.168.0.0, 24 subnet bits; mask is /24

Do you want to configure Serial0/0 interface? [yes]: y
您想配置serial0/0接口嗎?選Y
Some supported encapsulations are
ppp/hdlc/frame-relay/lapb/x25/atm-dxi/smds
Choose encapsulation type [hdlc]:
選擇封裝方式(默認的封裝方式是HDLC,您可根據與您的路由器相連選用的封裝類型來決

定用什么樣的封裝類型
No serial cable seen.
Choose mode from (dce/dte) [dte]:
(因為沒有連串口線所以會讓您選擇設備類型)
Configure IP on this interface? [yes]: y
(在接口上配置IP)
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 172.16.0.5
配置該接口的IP地址(在此地址為172.16.0.5)
Subnet mask for this interface [255.255.0.0] : 255.255.255.252
配置該接口的子網掩碼.(默認的是255.255.0.0,可以手工輸入修改為255.255.255.252)
Class B network is 172.16.0.0, 30 subnet bits; mask is /30

(以下配置同上)
Do you want to configure FastEthernet0/1 interface? [yes]:
Use the 100 Base-TX (RJ-45) connector? [yes]:
Operate in full-duplex mode? [no]: y
Configure IP on this interface? [yes]: y
IP address for this interface: 172.16.0.9
Subnet mask for this interface [255.255.0.0] : 255.255.255.252 Class B network is 172.16.0.0, 30 subnet bits; mask is /30

The following configuration command script was created:
(把您的配置顯示出來)
hostname aaa
enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/
enable password RouterA
line vty 0 4
password ccc
no snmp-server
!
ip routing
no bridge 1
!
interface FastEthernet0/0
media-type 100BaseX
full-duplex
ip address 192.168.0.1 255.255.255.0
!
interface Serial0/0
encapsulation hdlc
ip address 172.16.0.5 255.255.255.252
!
interface FastEthernet0/1
media-type 100BaseX
full-duplex
ip address 172.16.0.9 255.255.255.252
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
end

以下提示您是否保存這次設置
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.

Enter your selection [2]: 2
選擇2保存設置并存入NVRAM中
Building configuration...
[OK] Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started!
路由器重新啟動

00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
00:03:18: %IP-5-WEBINST_KILL: Terminating DNS process
00:03:24: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 16-May-00 12:26 by ccai
RouterA>
進入用戶模式
RouterA>en
Password:
RouterA#
進入全局模式
RouterA#sh run
查看現在運行的配置
Building configuration...

Current configuration:
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname RouterA
!
enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/
enable password bbb
!
memory-size iomem 25
ip subnet-zero
!
interface FastEthernet0/0
ip address 192.168.0.1 255.255.255.0
speed auto
full-duplex
!
interface Serial0/0
ip address 172.16.0.5 255.255.255.252
clockrate 2000000
!
interface FastEthernet0/1
ip address 172.16.0.9 255.255.255.252
speed auto
full-duplex
!
ip classless
no ip http server
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
line con 0
transport input none
line aux 0
line vty 0 4
password ccc
login
!
end