ADI公司的ADP1071-1/ADP1071-2是集成了隔離功能和SR驅動器及輕負載模式的反激式控制器，消除了變壓器和光耦合器件，降低了系統設計復雜性，成本和元件數量，并提高了系統可靠性。器件集成了誤差放大器和優于1%精度基準電壓，可編程開關頻率50 kHz - 600 kHz，主要用在隔離的DC/DC和AC/DC轉換器，通信和工業，小型基站，PoE供電設備，企業交換器和路由器。本文介紹了ADP1071-1/ADP1071-2主要特性，框圖，應用電路圖以及評估板ADP1071-1EVALZ和評估板ADP1071-2EBZ3.3V主要特性，電路圖，材料清單和PCB設計圖。

　　The ADP1071-1/ADP1071-2 are pulse-width modulation （PWM） current mode fixed frequency synchronous flyback controllers designed for isolated dc-to-dc power supplies. Analog Devices proprietary iCouplers? are integrated in the ADP1071-1/ADP1071-2 to eliminate the bulky signal trans-formers and optocouplers that transmit signals over the isolation boundary. Integrating the iCouplers reduces system design complexity， cost， and component count and improves overall system reliability. With the integrated isolators and metal-oxide semiconductor field effect transistor （MOSFET） drivers on both the primary and the secondary side， the ADP1071-1/ADP1071-2 offer a compact system level design and yield a higher efficiency than a diode rectified flyback converter at heavy loads.

　　Output regulation is achieved by sensing the output voltage on the secondary side， where the feedback and the PWM signals are transmitted between the primary and secondary sides through the iCouplers.

　　The ADP1071-1/ADP1071-2 are offered in a 16-lead SOIC_W package with an isolation voltage rating of 5 kV rms. The ADP1071-2 is designed for isolated dc-to-dc applications typically with an input voltage less than 36 V， and the ADP1071-1 targets high input voltage applications， in which the dc input voltage can exceed 60 V.

　　The ADP1071-1/ADP1071-2 offer features such as input current protection， output overvoltage protection （OVP）， undervoltage lockout （UVLO）， precision enable with adjustable hysteresis， overtemperature protection （OTP）， and power saving light load mode （LLM）。

　　ADP1071-1/ADP1071-2主要特性：

　　Current mode controller for flyback topology

　　ADP1071-1： programmable LLM or CCM for high VIN applications

　　ADP1071-2： forced CCM operation

　　Programmable slope compensation

　　Integrated 5 kV isolation with Analog Devices， Inc.， iCoupler technology

　　Wide voltage supply range

　　Primary VDD： up to 60 V （ADP1071-2 only）

　　Secondary VDD2： up to 36 V

　　Integrated 1 A primary side MOSFET driver

　　Integrated 1 A secondary side MOSFET drivers for synchronous rectification

　　Integrated error amplifier and 《1% accurate reference voltage

　　Programmable frequency range： 50 kHz to 600 kHz

　　Duty cycle clamp limit 85%

　　Programmable soft start and soft start from precharged load

　　Protection features such as short circuit， output overvoltage， and overtemperature protection

　　Power saving LLM using MODE pin （ADP1071-1only）

　　Cycle by cycle input overcurrent protection

　　Precision enable UVLO with hysteresis

　　Frequency synchronization

　　Safety and regulatory approvals （pending）

　　UL recognition

　　5000 V rms for 1 minute per UL 1577

　　CSA Component Acceptance Notice 5A

　　VDE certificate of conformity

　　DIN V VDE V 0884-10 （VDE V 0884-10）：2006-12

　　VIORM = 849 V peak

　　CQC certification per GB4943.1-2011

　　Available in 16-lead SOIC_W package

　　ADP1071-1/ADP1071-2應用：

　　Isolated dc-to-dc or ac-to-dc power conversion

　　Telecom， industrial

　　Small cell

　　PoE powered device

　　Enterprise switches and routers

　　圖1.ADP1071-1/ADP1071-2框圖

　　圖2.ADP1071-1/ADP1071-2外接起動電路和輔助電源的應用電路

　　圖3.ADP1071-1/ADP1071-2低輸入電壓反激應用電路圖

　　評估板ADP1071-1EVALZ

　　The ADP1071-1EVALZ allows users to evaluate the ADP1071-1 in flyback topology. The evaluation board is set up to act as an isolated power supply solution that incorporates three output voltages （+5.5 V， +24 V， and ?15 V） at a total rated power of 15 W. The evaluation board also provides 5 kV isolation in compact form factor， making it suitable for industrial applications， which usually have a variety of voltage rails.

　　Complete information about the ADP1071-1 is available in the ADP1071-1/ADP1071-2 data sheet. Consult the ADP1071-1/ ADP1071-2 data sheet in conjunction with this user guide when using the evaluation board.

　　評估板ADP1071-1EVALZ主要特性：

　　Full support evaluation kit for the ADP1071-1

　　15 W multioutput flyback topology

　　+24 V， +5.5 V， and ?15 V output voltage （VDC）

　　Light load mode （LLM） operation

　　Dedicated internal primary and secondary side MOSFET drivers

　　External reference signal tracking

　　Precision enabled undervoltage lockout with hysteresis

　　Short-circuit， output overvoltage， cycle by cycle input overcurrent， and overtemperature protection

　　Frequency synchronization

　　Soft start and soft stop functionality

　　圖4.評估板ADP1071-1EVALZ數字外形圖（正面）

　　圖5.評估板ADP1071-1EVALZ數字外形圖（背面）

　　圖6.變壓器電路圖

　　圖7.評估板ADP1071-1EVALZ電路圖

　　評估板ADP1071-1EVALZ材料清單：

　　圖8.評估板ADP1071-1EVALZ PCB設計圖（1）：左：板尺寸;右：底層絲印

　　圖9.評估板ADP1071-1EVALZ PCB設計圖（2）：左：頂層絲印;右：頂層布局

　　圖10.評估板ADP1071-1EVALZ PCB設計圖（3）：左：層2;右：層4

　　圖11.評估板ADP1071-1EVALZ PCB設計圖（4）：層3

　　評估板ADP1071-2EBZ3.3V

　　The ADP1071-2EBZ3.3V evaluation board allows users to evaluate the ADP1071-2 in a power supply application.

　　The ADP1071-2EBZ3.3V evaluation board is set up to act as an isolated power supply unit （PSU）， with a rated load of 3.3 Vdc 3 A from a 36 Vdc to 60 Vdc source. There is also an auxiliary output of 8.0 Vdc， 10 mA. The operation of the converter is in continuous conduction mode （CCM）。

　　All connectors and multiple test points allow easy access to all critical circuit nodes and pins of the ADP1071-2.

　　Multiple test points allow easy access to all critical circuit nodes and pins of the ADP1071-2.

　　Full data on the ADP1071-2 can be found in the ADP1071-2 data sheet， available from Analog Devices， Inc.， which must be consulted in conjunction with this user guide when using the evaluation board.

　　評估板ADP1071-2EBZ3.3V主要特性：

　　Full support evaluation kit for the ADP1071-2

　　10 W flyback topology

　　3.3 V output voltage （Vdc）

　　3 A steady state

　　Auxiliary output of 8.0 Vdc， 10 mA

　　Forced CCM operation

　　Integrated drivers primary side MOSFET and secondary side synchronous rectifier

　　External reference signal tracking

　　Precision enable undervoltage lockout with hysteresis

　　Short-circuit， output overvoltage， and overtemperature protection

　　Cycle by cycle input overcurrent protection

　　Frequency synchronization

　　Soft start and soft stop functionality

　　圖12.評估板ADP1071-2EBZ3.3V外形圖

　　圖13.評估板ADP1071-2EBZ3.3V框圖

　　圖14.評估板ADP1071-2EBZ3.3V電路圖

　　評估板ADP1071-2EBZ3.3V材料清單：

　　圖15.評估板ADP1071-2EBZ3.3V PCB設計圖（1）：頂層絲印

　　圖16.評估板ADP1071-2EBZ3.3V PCB設計圖（2）：底層絲印

　　圖17.評估板ADP1071-2EBZ3.3V PCB設計圖（3）：頂層布局

　　圖18.評估板ADP1071-2EBZ3.3V PCB設計圖（4）：層2

　　圖19.評估板ADP1071-2EBZ3.3V PCB設計圖（5）：層3

　　圖20.評估板ADP1071-2EBZ3.3V PCB設計圖（6）：層4

　　詳情請見：

　　和

　　以及

　　ADP1071-1-1071-2.pdf

　　ADP1071-1EVALZ-UG-1384.pdf

　　ADP1071-2EBZ3.3V.pdf