--- 產品詳情 ---
Regulated outputs (#) | 4 |
Vin (Min) (V) | 2.5 |
Vin (Max) (V) | 5.5 |
Iout (Max) (A) | 4 |
Rating | Catalog |
LDO | 0 |
Iq (Typ) (mA) | 0.006 |
Features | Adjustable Current Limit, Dynamic Voltage Scaling, Enable, I2C, Light Load Efficiency, Multiple Outputs, Output Discharge, Phase Interleaving, Power Good, Remote Sense, Synchronous Rectification |
Shutdown current (ISD) (Typ) (uA) | 1 |
Switching frequency (Typ) (kHz) | 3000 |
Configurability | Factory programmable, Software configurable |
- Fully Integrated Quad Buck, up to 4-A Programmable Maximum Output Current Per Buck
- Auto PWM-PFM and Forced-PWM Operations
- Programmable Output Voltage Slew Rate From 30 mV/μs to 0.5 mV/μs
- Input Voltage Range: 2.5 V to 5.5 V
- VOUT Range: 0.5 V to 3.36 V with DVS
- Programmable Start-Up and Shutdown Sequencing With Enable Signal
- I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz),
Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes - Interrupt Function with Programmable Masking
- Load Current Measurement
- Output Short-Circuit and Overload Protection
- Spread-Spectrum Mode for EMI Reduction
- The Four Buck Cores Operate 90° out of Phase Thereby Reducing Input Ripple Current
- Overtemperature Warning and Protection
- Undervoltage Lockout (UVLO)
The LP8758-E3 device is designed to meet power management requirements for low-power processors in mobile phones, network cards, and similar applications. The device contains four step-down DC-DC converter cores, providing four output voltage rails. The device is controlled by an I2C-compatible serial interface.
The automatic PWM-PFM (AUTO mode) operation maximizes efficiency over a wide output-current range.
The LP8758-E3 supports programmable start-up and shutdown sequencing synchronized to hardware Enable input signal.
The protection features include short-circuit protection, current limits, input supply UVLO, and temperature warning and shutdown functions. Several error flags are provided for status information of the device. In addition, the LP8758-E3 device supports load current measurement without the addition of external current sense resistors. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the inrush current.
為你推薦
-
TI數字多路復用器和編碼器SN54HC1512022-12-23 15:12
-
TI數字多路復用器和編碼器SN54LS1532022-12-23 15:12
-
TI數字多路復用器和編碼器CD54HC1472022-12-23 15:12
-
TI數字多路復用器和編碼器CY74FCT2257T2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS258A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74AHCT1582022-12-23 15:12
-
【PCB設計必備】31條布線技巧2023-08-03 08:09
相信大家在做PCB設計時,都會發現布線這個環節必不可少,而且布線的合理性,也決定了PCB的美觀度和其生產成本的高低,同時還能體現出電路性能和散熱性能的好壞,以及是否可以讓器件的性能達到最優等。在上篇內容中,小編主要分享了PCB線寬線距的一些設計規則,那么本篇內容,將針對PCB的布線方式,做個全面的總結給到大家,希望能夠?qū)︷B(yǎng)成良好的設計習慣有所幫助。1走線長度1634瀏覽量 -
電動汽車直流快充方案設計【含參考設計】2023-08-03 08:08
大功率直流充電系統架構大功率直流充電設計標準國家大功率充電標準“Chaoji”技術標準設計目標是未來可實現電動汽車充電5分鐘行駛400公里。“Chaoji”技術標準主要設計參數如下:最大電壓:目前1000V(可擴展到1500V);最大電流:帶冷卻系統500A(可擴展到600A);不帶冷卻系統150-200A;最大功率:900KW。大功率直流充電系統架構大功率 -
Buck電路的原理及器件選型指南2023-07-31 22:28
-
100W USB PD 3.0電源2023-07-31 22:27
-
千萬不要忽略PCB設計中線寬線距的重要性2023-07-31 22:27
想要做好PCB設計,除了整體的布線布局外,線寬線距的規則也非常重要,因為線寬線距決定著電路板的性能和穩定性。所以本篇以RK3588為例,詳細為大家介紹一下PCB線寬線距的通用設計規則。要注意的是,布線之前須把軟件默認設置選項設置好,并打開DRC檢測開關。布線建議打開5mil格點,等長時可根據情況設置1mil格點。PCB布線線寬01布線首先應滿足工廠加工能力,1726瀏覽量 -
基于STM32的300W無刷直流電機驅動方案2023-07-06 10:02
-
上新啦!開發板僅需9.9元!2023-06-21 17:43
-
參考設計 | 2KW AC/DC數字電源方案2023-06-21 17:43
-
千萬不能小瞧的PCB半孔板2023-06-21 17:34