資料介紹
USB 2.0 Specification Engineering Change Notice (ECN) #1: Mini-B connector
Date: 10/20/2000
Reason for ECN:
The USB 2.0 specified device-side connector – the B connector – is too large for use with
a new generation of handheld and mobile devices, e.g., cell phones which would benefit
from connectivity to the PC. This ECN incorporates a specification of a device-side mini
connector (hereafter referred to as a mini-B connector). The new connector only applies
to upstream facing ports, i.e., connectors on devices.
Summary of ECN:
The bulk of the ECN specifies the mechanical requirements for the mini-B plug,
receptacle and cable assembly. It also identifies the usage scope of this connector. The
last part of the ECN describes the minimum test criteria and performance requirements
for the new connector.
Benefits of ECN:
The ECN enables standardization of miniature device-side USB connectors and
consequent economies of scales and lower cost for a new and growing class of devices
which will benefit from connectivity to the PC. The standardization also allows
leveraging of the compliance test and certification model which is already in place for
USB connectors.
Assessment of Impact on Current Specification and Current USB Products:
The connector specified in the ECN will not have any impact on hardware or software of
existing USB products. The current USB spec already allows for vendor-specific device
side connectors – such cable assemblies are called captive assemblies. All that the ECN
does is to identify one such connector for use in devices which need the smaller size of
connector. There is a potential for some end-user confusion because of two standard
cable options; but this can be mitigated by appropriate end-user education.
Structure of ECN:
The ECN is in the form of a new Chapter 6 with the mini-B connector requirements
inserted into the appropriate locations. This format enables specification of the new
connector in context.
Date: 10/20/2000
Reason for ECN:
The USB 2.0 specified device-side connector – the B connector – is too large for use with
a new generation of handheld and mobile devices, e.g., cell phones which would benefit
from connectivity to the PC. This ECN incorporates a specification of a device-side mini
connector (hereafter referred to as a mini-B connector). The new connector only applies
to upstream facing ports, i.e., connectors on devices.
Summary of ECN:
The bulk of the ECN specifies the mechanical requirements for the mini-B plug,
receptacle and cable assembly. It also identifies the usage scope of this connector. The
last part of the ECN describes the minimum test criteria and performance requirements
for the new connector.
Benefits of ECN:
The ECN enables standardization of miniature device-side USB connectors and
consequent economies of scales and lower cost for a new and growing class of devices
which will benefit from connectivity to the PC. The standardization also allows
leveraging of the compliance test and certification model which is already in place for
USB connectors.
Assessment of Impact on Current Specification and Current USB Products:
The connector specified in the ECN will not have any impact on hardware or software of
existing USB products. The current USB spec already allows for vendor-specific device
side connectors – such cable assemblies are called captive assemblies. All that the ECN
does is to identify one such connector for use in devices which need the smaller size of
connector. There is a potential for some end-user confusion because of two standard
cable options; but this can be mitigated by appropriate end-user education.
Structure of ECN:
The ECN is in the form of a new Chapter 6 with the mini-B connector requirements
inserted into the appropriate locations. This format enables specification of the new
connector in context.
下載該資料的人也在下載
下載該資料的人還在閱讀
更多 >
- USB2.0規范 32次下載
- USB端口供電的鋰離子_鋰聚合物電池充電 6次下載
- USB端口供電的詳細資料和USB的其他功能詳細概述
- usb 2.0 規范 16次下載
- USB開發板功能特點 57次下載
- USB2.0設備的設計與開發_邊海龍 0次下載
- 基于層次模型的USB2.0接口芯片IP核固件的設計 24次下載
- USB2.0接口芯片IP核固件設計 59次下載
- 借助USB來完成系統配置
- XR21V1414 4通道全速USB UART數據手冊
- XR21V1410 1通道全速USB UART數據手冊
- XR21V1410 1通道全速USB UART標準規范手冊
- USB On The Go技術概述
- USB2.0規范與EZ-USB FX2高速外設控制器
- ISP1581中文資料,ISP1581數據手冊 (USB 2
- USB 2.0信號質量測試 1646次閱讀
- Diodes公司USB 2.0信號調節器PI5USB212產品介紹 791次閱讀
- usb2.0接口與usb3.0接口有什么區別 2.7w次閱讀
- 基于CY7C68013芯片對MPEG視頻卡進行改進設計方案 877次閱讀
- 采用CY7C646xx系列實現USB接口系統的設計 1359次閱讀
- USB2.0設備接口IP核的設計實用性分析 1859次閱讀
- 四代USB規范的詳細說明 6231次閱讀
- USB 2.0和USB 3.0的基本區別對比分析 2.3w次閱讀
- USB OTG的工作原理解析 1.7w次閱讀
- USB2.0主機測試方法及控制原理解析 8646次閱讀
- USB 3.0電纜與USB 2.0電纜對比分析 5669次閱讀
- USB 3.2接口的特征, USB 3.0和USB 2.0的區別 8.6w次閱讀
- USB2.0和USB3.0區別是什么詳解! 6w次閱讀
- USB電池充電規范1.2版概述及適配器仿真器的重要性 9096次閱讀
- 精通USB 2.0集線器電源管理 4644次閱讀
下載排行
本周
- 1貼片三極管上的印字與真實名稱的對照表詳細說明
- 0.50 MB | 76次下載 | 1 積分
- 2Altium Designer AD 25 軟件安裝包下載
- 0.00 MB | 3次下載 | 免費
- 3Altium Designer 23 軟件下載
- 0.00 MB | 2次下載 | 免費
- 4Altium Designer 22.11.1軟件安裝包下載
- 0.00 MB | 1次下載 | 免費
- 5PADS Professional vx 2.11 安裝包
- 0.00 MB | 1次下載 | 5 積分
- 6高頻率變壓器的設計
- 0.03 MB | 1次下載 | 1 積分
- 7ANT8817 1%3.5W/3.7V,同步自適應升壓,超長續航,H類防破音單聲道音頻功放中文手冊
- 1.11 MB | 1次下載 | 免費
- 8NS6326 4-30V輸入5V/3A輸出同步降壓穩壓器中文手冊
- 1.22 MB | 次下載 | 免費
本月
- 1蘇泊爾電磁爐線路的電路原理圖資料合集
- 2.02 MB | 286次下載 | 5 積分
- 2長虹液晶電視R-HS310B-5HF01的電源板電路原理圖
- 0.46 MB | 87次下載 | 5 積分
- 3貼片三極管上的印字與真實名稱的對照表詳細說明
- 0.50 MB | 76次下載 | 1 積分
- 4U盤一鍵制作
- 23.84 MB | 41次下載 | 免費
- 5AI智能眼鏡產業鏈分析
- 4.43 MB | 39次下載 | 免費
- 6AO4803A雙P通道增強型場效應晶體管的數據手冊
- 0.11 MB | 28次下載 | 2 積分
- 7長虹液晶彩電LS29機芯的技術資料說明
- 3.42 MB | 16次下載 | 2 積分
- 8TP4055 500mA線性鋰離子電池充電器中文手冊
- 0.75 MB | 9次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935127次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420064次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233089次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191387次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183342次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81586次下載 | 10 積分
- 7Keil工具MDK-Arm免費下載
- 0.02 MB | 73815次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65988次下載 | 10 積分
評論