電子發燒友App
創作
發文章
發帖 
提問 
發資料
發視頻資料介紹
Table of Contents
AD7303 - No-OS Driver for Renesas Microcontroller Platforms
Supported Devices
Evaluation Boards
Overview
The AD7303 is a dual, 8-bit voltage out DAC that operates from a single +2.7 V to +5.5 V supply. Its on-chip precision output buffers allow the DAC outputs to swing rail to rail. This device uses a versatile 3-wire serial interface that operates at clock rates up to 30 MHz, and is compatible with QSPI, SPI, microwire and digital signal processor interface standards. The serial input register is sixteen bits wide; 8 bits act as data bits for the DACs, and the remaining eight bits make up a control register.
The on-chip control register is used to address the relevant DAC, to power down the complete device or an individual DAC, to select internal or external reference and to provide a synchronous loading facility for simultaneous update of the DAC outputs with a software LDAC function.
The low power consumption of this part makes it ideally suited to portable battery operated equipment. The power consumption is 7.5 mW max at 3 V, reducing to less than 3 μW in full power-down mode.
The AD7303 is available in an 8-pin plastic dual in-line package, 8-lead SOIC and microSOIC packages.
The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for different microcontroller platforms.
Driver Description
The driver contains two parts:
- The driver for the AD7303 part, which may be used, without modifications, with any microcontroller.
- The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver.
The Communication Driver has a standard interface, so the AD7303 driver can be used exactly as it is provided.
There are three functions which are called by the AD7303 driver:
- SPI_Init() – initializes the communication peripheral.
- SPI_Write() – writes data to the device.
- SPI_Read() – reads data from the device.
SPI driver architecture
The following functions are implemented in this version of AD7303 driver:
| Function | Description |
|---|---|
| char AD7303_Init(void) | Initializes the SPI communication peripheral. |
| void AD7303_Write(unsigned char controlReg, unsigned char dataReg) | Sends data to AD7303. |
Downloads
- PmodDA1 Demo for RL78G14: https://github.com/analogdevicesinc/no-OS/tree/master/Renesas/RL78G14/PmodDA1
- RL78G14 Common Drivers: https://github.com/analogdevicesinc/no-OS/tree/master/Renesas/RL78G14/Common
Renesas RL78G13 Quick Start Guide
This section contains a description of the steps required to run the AD7303 demonstration project on a Renesas RL78G13 platform.
Required Hardware
Required Software
Hardware Setup
A PmodDA1 has to be connected to the PMOD1 connector, pins 1 to 6 (see image below).
Reference Project Overview
The reference project:
- outputs a 3 Hz sine wave on channel A;
- outputs a specific value(zero scale, middle scale and full scale) every second on channel B.
Software Project Tutorial
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RL78G13 for controlling and monitoring the operation of the ADI part.
- Run the IAR Embedded Workbench for Renesas RL78 integrated development environment.
- Choose to create a new project (Project – Create New Project).
- Select the RL78 tool chain, the Empty project template and click OK.
- Select a location and a name for the project (ADIEvalBoard for example) and click Save.
- Open the project’s options window (Project – Options).
- From the Target tab of the General Options category select the RL78 – R5F100LE device.
- From the Setup tab of the Debugger category select the TK driver and click OK.
- Extract the files from the lab .zip archive and copy them into the project’s folder.
- The new source files have to be included into the project. Open the Add Files… window (Project – Add Files…), select all the copied files and click open.
- At this moment, all the files are included into the project.
- The project is ready to be compiled and downloaded on the board. Press the F7 key to compile it. Press CTRL + D to download and debug the project.
- A window will appear asking to configure the emulator. Keep the default settings and press OK.
- To run the project press F5.
Renesas RL78G14 Quick Start Guide
This section contains a description of the steps required to run the AD7303 demonstration project on a Renesas RL78G14 platform using the PmodDA1.
Required Hardware
Required Software
- The AD7303 demonstration project for the Renesas RL78G14 platform.
The AD7303 demonstration project for the Renesas RL78G14 platform consists of three parts: the AD7303 Driver, the PmodDA1 Demo for RL78G14 and the RL78G14 Common Drivers.
All three parts have to be downloaded.
Hardware Setup
A PmodDA1 has to be connected to the PMOD1 connector, pins 1 to 6 (see image below).
Reference Project Overview
The reference project:
- outputs a 4 Hz sine wave on channel A;
- outputs a specific value(zero scale, middle scale and full scale) every second on channel B.
Software Project Tutorial
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RL78G14 for controlling and monitoring the operation of the ADI part.
- Run the IAR Embedded Workbench for Renesas RL78 integrated development environment.
- Choose to create a new project (Project – Create New Project).
- Select the RL78 tool chain, the Empty project template and click OK.
- Select a location and a name for the project (ADIEvalBoard for example) and click Save.
- Open the project’s options window (Project – Options).
- From the Target tab of the General Options category select the RL78 – R5F104PJ device.
- From the Setup tab of the Debugger category select the TK driver and click OK.
- Copy the downloaded files into the project's folder.
- The new source files have to be included into the project. Open the Add Files… window (Project – Add Files…), select all the copied files and click open.
- At this moment, all the files are included into the project.
- The project is ready to be compiled and downloaded on the board. Press the F7 key to compile it. Press CTRL + D to download and debug the project.
- A window will appear asking to configure the emulator. Keep the default settings and press OK.
- To run the project press F5.
Renesas RX62N Quick Start Guide
This section contains a description of the steps required to run the AD7303 demonstration project on a Renesas RX62N platform.
Required Hardware
Required Software
Hardware Setup
A PmodAD5 has to be interfaced with the Renesas Demonstration Kit (RDK) for RX62N:
PmodDA1 Pin 1 (CS) → YRDKRX62N J8 connector Pin 15 PmodDA1 Pin 2 (MOSI) → YRDKRX62N J8 connector Pin 19 PmodDA1 Pin 4 (CLK) → YRDKRX62N J8 connector Pin 20 PmodDA1 Pin 5 (GND) → YRDKRX62N J8 connector Pin 4 PmodDA1 Pin 6 (VCC) → YRDKRX62N J8 connector Pin 3
Reference Project Overview
The reference project outputs a 3 Hz sinewave on channel A and a specific value every second on channel B.
Software Project Setup
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RX62N for controlling and monitoring the operation of the ADI part.
- Run the High-performance Embedded Workshop integrated development environment.
- A window will appear asking to create or open project workspace. Choose “Create a new project workspace” option and press OK.
- From “Project Types” option select “Application”, name the Workspace and the Project “ADIEvalBoard”, select the “RX” CPU family and “Renesas RX Standard” tool chain. Press OK.
- A few windows will appear asking to configure the project:
- In the “Select Target CPU” window, select “RX600” CPU series, “RX62N” CPU Type and press Next.
- In the “Option Setting” windows keep default settings and press Next.
- In the “Setting the Content of Files to be generated” window select “None” for the “Generate main() Function” option and press Next.
- In the “Setting the Standard Library” window press “Disable all” and then Next.
- In the “Setting the Stack Area” window check the “Use User Stack” option and press Next.
- In the “Setting the Vector” window keep default settings and press Next.
- In the “Setting the Target System for Debugging” window choose “RX600 Segger J-Link” target and press Next.
- In the “Setting the Debugger Options” and “Changing the Files Name to be created” windows keep default settings, press Next and Finish.
- The workspace is created.
- The RPDL (Renesas Peripheral Driver Library) has to integrated in the project. Unzip the RPDL files (double-click on the file “RPDL_RX62N.exe”). Navigate to where the RPDL files were unpacked and double-click on the “Copy_RPDL_RX62N.bat” to start the copy process. Choose the LQFP package, type the full path where the project was created and after the files were copied, press any key to close the window.
- The new source files have to be included in the project. Use the key sequence Alt, P, A to open the “Add files to project ‘ADIEvalBoard’” window. Double click on the RPDL folder. From the “Files of type” drop-down list, select “C source file (*.C)”. Select all of the files and press Add.
- To avoid conflicts with standard project files remove the files “intprg.c” and “vecttbl.c” which are included in the project. Use the key sequence Alt, P, R to open the “Remove Project Files” window. Select the files, click on Remove and press OK.
- Next the new directory has to be included in the project. Use the key sequence Alt, B, R to open the “RX Standard Toolchain” window. Select the C/C++ tab, select “Show entries for: Include file directories” and press Add. Select “Relative to: Project directory”, type “RPDL” as sub-directory and press OK.
- The library file path has to be added in the project. Select the Link/Library tab, select “Show entries for: Library files” and press Add. Select “Relative to: Project directory”, type “RPDL/RX62N_library” as file path and press OK.
- Because the “intprg.c” file was removed the “PIntPrg” specified in option “start” has to be removed. Change “Category” to “Section”. Press “Edit”, select “PIntPRG” and press “Remove”. From this window the address of each section can be also modified. After all the changes are made press OK two times.
- At this point the files extracted from the zip file located in the “Software Tools” section have to be added into the project. Copy all the files from the archive into the project folder.
- Now, the files have to be included in the project. Use the key sequence Alt, P, A to open the “Add files to project ‘ADIEvalBoard’” window. Navigate into ADI folder. From the “Files of type” drop-down list, select “Project Files”. Select all the copied files and press Add.
- Now, the project is ready to be built. Press F7. The message after the Build Process is finished has to be “0 Errors, 0 Warnings”. To run the program on the board, you have to download the firmware into the microprocessor’s memory.
More information
- Example questions:
- An error occurred while fetching this feed: http://ez.analog.com/community/feeds/allcontent/atom?community=2077
- AD5160-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7193-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7303-適用于單片機平臺的無操作系統驅動程序
- AD5541A-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7091R-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD74xx-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5933-瑞薩微控制器平臺的無操作系統驅動程序
- ADXL345-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7780-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5781-適用于瑞薩微控制器平臺的無操作系統驅動程序
- ADF7023-用于瑞薩微控制器平臺的無操作系統驅動程序
- ADP5589-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD799x-用于瑞薩微控制器平臺的無操作系統驅動程序
- ADT7420-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7156-適用于瑞薩微控制器平臺的無操作系統驅動程序
- 瑞薩CTSU程序在向嵌入式OS操作系統移植時的注意事項 373次閱讀
- 深度解析全球操作系統格局 1271次閱讀
- 實時時鐘為微控制器系統增加了精確的計時功能 1382次閱讀
- 了解和使用無操作系統和平臺驅動程序 1295次閱讀
- 瑞薩快速接入式物聯網平臺為快速原型開發提供構建模塊 596次閱讀
- 基于具有USB功能的STM32微控制器 3826次閱讀
- 微控制器的主要應用在哪里 9301次閱讀
- 嵌入式Linux內核的驅動程序開發是怎樣的 1524次閱讀
- 淺談電腦驅動程序的工作原理 詳解電腦驅動程序意義 3w次閱讀
- 基于嵌入式Linux內核的系統設備驅動程序開發設計 1209次閱讀
- 基于Linux2.6.30開發DS18B20的驅動程序的類型和文件操作接口函數詳解 1500次閱讀
- 基于STM32的數字PDA系統軟件系統設計 1562次閱讀
- 8155驅動程序 3284次閱讀
- 基于STM32ZET6控制器的數字PDA系統的設計 1577次閱讀
- 基于FPGA嵌入式系統的設備驅動開發 2339次閱讀
上傳資料賺積分下載排行
本周
- 1AN-1267: 使用ADSP-CM408F ADC控制器的電機控制反饋采樣時序
- 1.41MB | 3次下載 | 免費
- 2AN158 GD32VW553 Wi-Fi開發指南
- 1.51MB | 2次下載 | 免費
- 3AN148 GD32VW553射頻硬件開發指南
- 2.07MB | 1次下載 | 免費
- 4AN-1154: 采用恒定負滲漏電流優化ADF4157和ADF4158 PLL的相位噪聲和雜散性能
- 199.28KB | 次下載 | 免費
- 5AN-960: RS-485/RS-422電路實施指南
- 380.8KB | 次下載 | 免費
- 6EE-249：使用VisualDSP在ADSP-218x DSP上實現軟件疊加
- 60.02KB | 次下載 | 免費
- 7AN-1111: 使用ADuCM360/ADuCM361時的降低功耗選項
- 306.09KB | 次下載 | 免費
- 8AN-904: ADuC7028評估板參考指南
- 815.82KB | 次下載 | 免費
本月
- 1ADI高性能電源管理解決方案
- 2.43 MB | 450次下載 | 免費
- 2免費開源CC3D飛控資料（電路圖&PCB源文件、BOM、
- 5.67 MB | 138次下載 | 1 積分
- 3基于STM32單片機智能手環心率計步器體溫顯示設計
- 0.10 MB | 130次下載 | 免費
- 4使用單片機實現七人表決器的程序和仿真資料免費下載
- 2.96 MB | 44次下載 | 免費
- 5美的電磁爐維修手冊大全
- 1.56 MB | 24次下載 | 5 積分
- 6如何正確測試電源的紋波
- 0.36 MB | 18次下載 | 免費
- 7感應筆電路圖
- 0.06 MB | 10次下載 | 免費
- 8萬用表UT58A原理圖
- 0.09 MB | 9次下載 | 5 積分
總榜
- 1matlab軟件下載入口
- 未知 | 935121次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420062次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233088次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191367次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183335次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81581次下載 | 10 積分
- 7Keil工具MDK-Arm免費下載
- 0.02 MB | 73810次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65988次下載 | 10 積分
工商網監
評論