• Highlights
  • High-Performance Digital Media System-on-Chip (DMSoC)
  • Up to 300-MHz ARM926EJ-S Clock Rate
  • Two Video Image Co-processors (HDVICP, MJCP) Engines
  • Supports a Range of Encode, Decode, and Video Quality Operations
  • Video Processing Subsystem
    • HW Face Detect Engine
    • Resize Engine from 1/16x to 8x
    • 16-Bit Parallel AFE (Analog Front-End) Interface Up to 120 MHz
    • 4:2:2 (8-/16-bit) Interface
    • 8-/16-bit YCC and Up to 24-Bit RGB888 Digital Output
    • 3 DACs for HD Analog Video Output
    • Hardware On-Screen Display (OSD)
  • Capable of 720p 30fps H.264 video processing
    Note: 216-MHz is only capable of D1 processing
  • Peripherals include EMAC, USB 2.0 OTG, DDR2/NAND, 5 SPIs, 2 UARTs, 2 MMC/SD/SDIO, Key Scan
  • 8 Different Boot Modes and Configurable Power-Saving Modes
  • Pin-to-pin and software compatible with DM368
  • Extended temperature (-40°C - 85°C) available for 300-Mhz device
  • 3.3-V and 1.8-V I/O, 1.2-V/1.35-V Core
  • 338-Pin Ball Grid Array at 65nm Process Technology
• High-Performance Digital Media System-on-Chip (DMSoC)
  • 216-, 270-, 300-MHz ARM926EJ-S Clock Rate
  • Fully Software-Compatible With ARM9™
• ARM926EJ-S™ Core
  • Support for 32-Bit and 16-Bit (Thumb® Mode) Instruction Sets
  • DSP Instruction Extensions and Single Cycle MAC
  • ARM® Jazelle® Technology
  • EmbeddedICE-RT Logic for Real-Time Debug
• ARM9 Memory Architecture
  • 16K-Byte Instruction Cache
  • 8K-Byte Data Cache
  • 32K-Byte RAM
  • 16K-Byte ROM
  • Little Endian
• Two Video Image Co-processors (HDVICP, MJCP) Engines
  • Support a Range of Encode and Decode Operations
  • H.264, MPEG4, MPEG2, MJPEG, JPEG, WMV9/VC1
• Video Processing Subsystem
  • Front End Provides:
    • HW Face Detect Engine
    • Hardware IPIPE for Real-Time Image Processing
      • Resize Engine
        • Resize Images From 1/16× to 8×
        • Separate Horizontal/Vertical Control
        • Two Simultaneous Output Paths
    • IPIPE Interface (IPIPEIF)
    • Image Sensor Interface (ISIF) and CMOS Imager Interface
    • 16-Bit Parallel AFE (Analog Front End) Interface Up to 120 MHz
    • Glueless Interface to Common Video Decoders
    • BT.601/BT.656/BT.1120 Digital YCbCr 4:2:2 (8-/16-Bit Module
    • Histogram Module
    • Lens distortion correction module (LDC)
    • Hardware 3A statistics collection module (H3A)
  • Back End Provides:
    • Hardware On-Screen Display (OSD)
    • Composite NTSC/PAL video encoder output
    • 8-/16-bit YCC and Up to 24-Bit RGB888 Digital Output
    • 3 DACs for HD Analog Video Output
    • LCD Controller
    • BT.601/BT.656 Digital YCbCr 4:2:2 (8-/16-Bit) Interface
• Analog-to-Digital Convertor (ADC)
• Power Management and Real Time Clock Subsystem (PRTCSS)
  • Real Time Clock
• 16-Bit Host-Port Interface (HPI)
• 10/100 Mb/s Ethernet Media Access Controller (EMAC) - Digital Media
  • IEEE 802.3 Compliant
  • Supports Media Independent Interface (MII)
  • Management Data I/O (MDIO) Module
• Key Scan
• Voice Codec
• External Memory Interfaces (EMIFs)
  • DDR2 and mDDR SDRAM 16-bit wide EMIF With 256 MByte Address Space (1.8-V I/O)
  • Asynchronous16-/8-bit Wide EMIF (AEMIF)
    • Flash Memory Interfaces
      • NAND (8-/16-bit Wide Data)
      • 16 MB NOR Flash, SRAM
      • OneNAND(16-bit Wide Data)
• Flash Card Interfaces
  • Two Multimedia Card (MMC) / Secure Digital (SD/SDIO)
  • SmartMedia/xD
• Enhanced Direct-Memory-Access (EDMA) Controller (64 Independent Channels)
• USB port with Integrated 2.0 High-Speed PHY that Supports
  • USB 2.0 High-Speed Device
  • USB 2.0 High-Speed Host (mini-host, supporting one external device)
  • USB On The Go (HS-USB OTG)
• Four 64-Bit General-Purpose Timers (each configurable as two 32-bit timers)
• One 64-Bit Watch Dog Timer
• Two UARTs (One fast UART with RTS and CTS Flow Control)
• Five Serial Port Interfaces (SPI) each with two Chip-Selects
• One Master/Slave Inter-Integrated Circuit (I²C) Bus™
• One Multi-Channel Buffered Serial Port (McBSP)
  • I2S
  • AC97 Audio Codec Interface
  • S/PDIF via Software
  • Standard Voice Codec Interface (AIC12)
  • SPI Protocol (Master Mode Only)
  • Direct Interface to T1/E1 Framers
  • Time Division Multiplexed Mode (TDM)
  • 128 Channel Mode
• Four Pulse Width Modulator (PWM) Outputs
• Four RTO (Real Time Out) Outputs
• Up to 104 General-Purpose I/O (GPIO) Pins (Multiplexed with Other Device Functions)
• Boot Modes
  • On-Chip ARM ROM Bootloader (RBL) to Boot From NAND Flash, MMC/SD, UART, USB, SPI, EMAC, or HPI
  • AEMIF (NOR and OneNAND)
• Configurable Power-Saving Modes
• Crystal or External Clock Input (typically 19.2 Mhz, 24 MHz, 27 Mhz or 36 MHz)
• Flexible PLL Clock Generators
• Debug Interface Support
  • IEEE-1149.1 (JTAG™) Boundary-Scan-Compatible
  • ETB (Embedded Trace Buffer) with 4K-Bytes Trace Buffer memory
  • Device Revision ID Readable by ARM
• 338-Pin Ball Grid Array (BGA) Package (ZCE Suffix), 0.65-mm Ball Pitch
• 65nm Process Technology
• 3.3-V and 1.8-V I/O, 1.2-V/ 1.35-V Internal
• Community Reesources
  • TI E2E Community
  • TI Embedded Processors Wiki

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this document.

Windows is a trademark of Microsoft.

All other trademarks are the property of their respective owners.